|
April 2011 |
The new FGSW-2612PVS provides 24 10/100Mbps Fast
Ethernet ports and 2 Gigabit TP /SFP combo ports, the two Gigabit ports
either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through
SFP (Small Factor Pluggable) interface. The distance can be extended
from 100 meters (TP), 550 meters (Multi-mode fiber), up to above
10/50/70/120 kilometers (Single-mode fiber).
Key Features
- Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3z and IEEE 802.3ab Gigabit Ethernet standard
- 24-Port 10/100Mbps Fast Ethernet Switch
- 2-Port Gigabit TP/SFP combo ports
- 24-Port PoE output
- Each Switching port supports auto-negotiation-10/20, 100/200Mbps supported
- Supports IEEE 802.3af 15.4 watts power output on each port
- Auto-MDI/MDI-X detection on each RJ-45 port
- Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame flow control (full- duplex)
- High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
- 8K MAC address table, automatic source address learning and ageing
- 512K Bytes packet buffers
- Web interface for Switch basic management and setup
- Supports up to 26 IEEE 802.1Q or Port-based VLAN groups
- Supports up to 7 Trunk groups, each trunk for up to maximum 8 port with 800Mbps bandwidth
- Port mirroring allows to monitor the traffic across any port in real time
- Supports QoS and bandwidth to control each port
- Supports Access Control List function
- 19-inch rack mount size
- Internal full-range power supply suitable for worldwide use
- EMI standards comply with FCC, CE class A
Specifications
| Hardware Specification |
| Ports |
24 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports |
| Module Slots |
2 Gigabit TP/SFP combo ports |
| PoE ports |
12( port 1 to port 12) |
| Switch Processing Scheme |
Store-and-forward |
| Throughput (packet per second) |
6.547Mpps |
| Switch fabric |
8.8Gbps |
| Address Table |
8K entries |
| Share data Buffer |
512K Bytes |
| Flow Control |
Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex |
| Dimensions (W x D x H) |
440 x 265 x 44 mm, 1U height |
| Weight |
3.51kg |
| Power Requirement |
100~240V AC, 50-60 Hz |
| Switch Power Consumption / Dissipation |
13.5 Watts maximum / 46 BTU/hr maximum |
| PoE Power Consumption / Dissipation |
130 Watts maximum / 443 BTU/hr maximum |
| Temperature |
Operating: 0~50 degree C, Storage -40~70 degree C |
| Humidity Operating |
10% to 90%, Storage: 5% to 95% (Non-condensing) |
| Smart function |
| System Configuration |
Web interface |
| Port Status |
Display per port’s disable/enable status, per port’s link status and speed duplex mode. Also the Flow control status |
| Port Configuration |
Per
port disable/enable, Auto-negotiation disable/enable. 10/100Mbps full
and half duplex mode selection. Flow control disable/enable and
bandwidth control on each port |
| Trunk Configuration |
Supports 7 groups of 8-Port trunk |
| VLAN Configuration |
Maximum up to 26 VLAN groups for port-based VLAN |
| Port Monitoring |
One Mirroring port to monitor one mirrored port. The monitor modes are RX, TX and RX & TX |
| QoS Configuration |
IEEE 802.1p QoS on each port |
| Port counters |
Display detail traffic counters on each port |
| Access Control List |
Supports up to 16 Access Control list group |
| PoE Ports configuration |
Per PoE port disable / enable and power feeding priority assign |
| PoE Ports Status |
Per PoE port status such as Enable or disable, power consumption and current. |
| Standards Conformance |
| Regulation Compliance |
FCC Part 15 Class A, CE |
| Standards Compliance |
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3z(Gigabit Ethernet)
IEEE 802.3af Power over Ethernet
IEEE 802.3x (Full-duplex flow control)
IEEE 802.1p QoS |
Click here to return
FGSW-2612PVS
|
|
|
April 2011 |
The PLANET FGSW-2620PVS provides 24 10/100Mbps Fast
Ethernet ports and 2 Gigabit  TP/SFP combo ports, the two Gigabit ports
either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through
SFP (Small Factor Pluggable) interface. The distance can be extended
from 100 meters (TP), 550 meters (Multi-mode fiber), up to above
10/50/70/120 kilometers (Single-mode fiber).
The Web Smart PoE Switches are equipped with non-blocking 8.8Gbps
backplane greatly simplifies the tasks of upgrading your LAN to cater
for increased bandwidth demands. The PoE in-line power follows the
standard IEEE 802.3af for making the FGSW-2620PVS
able to power on 24/12 PoE devices at the distance up to 100 meters
through the 4-pair Cat 5/5e UTP wire.
Key Features
- Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3z and IEEE 802.3ab Gigabit Ethernet standard
- 24-Port 10/100Mbps Fast Ethernet Switch
- 2-Port Gigabit TP/SFP combo ports
- 24-Port PoE output
- Each Switching port supports auto-negotiation-10/20, 100/200Mbps supported
- Supports IEEE 802.3af 15.4 watts power output on each port
- Auto-MDI/MDI-X detection on each RJ-45 port
- Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame flow control (full- duplex)
- High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
- 8K MAC address table, automatic source address learning and ageing
- 512K Bytes packet buffers
- Web interface for Switch basic management and setup
- Supports up to 26 IEEE 802.1Q or Port-based VLAN groups
- Supports up to 7 Trunk groups, each trunk for up to maximum 8 port with 800Mbps bandwidth
- Port mirroring allows to monitor the traffic across any port in real time
- Supports QoS and bandwidth to control each port
- Supports Access Control List function
- 19-inch rack mount size
- Internal full-range power supply suitable for worldwide use
- EMI standards comply with FCC, CE class A
Specifications
| Hardware Specification |
| Ports |
24 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports |
| Module Slots |
2 Gigabit TP/SFP combo ports |
| PoE ports |
24( port 1 to port 24) |
| Switch Processing Scheme |
Store-and-forward |
| Throughput (packet per second) |
6.547Mpps |
| Switch fabric |
8.8Gbps |
| Address Table |
8K entries |
| Share data Buffer |
512K Bytes |
| Flow Control |
Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex |
| Dimensions (W x D x H) |
440 x 265 x 44 mm, 1U height |
| Weight |
3.87kg |
| Power Requirement |
100~240V AC, 50-60 Hz |
| Switch Power Consumption / Dissipation |
13.5 Watts maximum / 46 BTU/hr maximum |
| PoE Power Consumption / Dissipation |
260 Watts maximum / 887 BTU/hr maximum |
| Temperature |
Operating: 0~50 degree C, Storage -40~70 degree C |
| Humidity Operating |
10% to 90%, Storage: 5% to 95% (Non-condensing) |
| Smart function |
| System Configuration |
Web interface |
| Port Status |
Display per port’s disable/enable status, per port’s link status and speed duplex mode. Also the Flow control status |
| Port Configuration |
Per
port disable/enable, Auto-negotiation disable/enable. 10/100Mbps full
and half duplex mode selection. Flow control disable/enable and
bandwidth control on each port |
| Trunk Configuration |
Supports 7 groups of 8-Port trunk |
| VLAN Configuration |
Maximum up to 26 VLAN groups for port-based VLAN |
| Port Monitoring |
One Mirroring port to monitor one mirrored port. The monitor modes are RX, TX and RX & TX |
| QoS Configuration |
IEEE 802.1p QoS on each port |
| Port counters |
Display detail traffic counters on each port |
| Access Control List |
Supports up to 16 Access Control list group |
| PoE Ports configuration |
Per PoE port disable / enable and power feeding priority assign |
| PoE Ports Status |
Per PoE port status such as Enable or disable, power consumption and current. |
| Standards Conformance |
| Regulation Compliance |
FCC Part 15 Class A, CE |
| Standards Compliance |
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3z(Gigabit Ethernet)
IEEE 802.3af Power over Ethernet
IEEE 802.3x (Full-duplex flow control)
IEEE 802.1p QoS |
Click here to return
FGSW-2620PVS
|
|
|
April 2011 |
|
The WGSW-24010 is a powerful, high-performance 24G + 1 Mini-GBIC
10/100/1000Mbps F ast Ethernet and Gigabit managed switch with twenty-four
10/100/1000Mbps ports and 1-SFP Mini-GBIC interfaces. The SFP Mini-GBIC
interfaces for fiber extension is ideal for backbone connection
to other workgroup products.
All RJ-45 copper interfaces support 10/100/1000Mbps Auto-Negotiation
for optimal speed detection through RJ-45 Category 6, 5 or 5e cables.
Also, all the ports support Auto-MDI/MDI-X that can detect the type
of connection to any Ethernet device without requiring special straight
or crossover cables.
Key Features
- Complies with IEEE802.3, 10Base-T, IEEE802.3u, 100Base-TX and IEEE802.3ab, 1000Base-T and IEEE802.z 1000Base-SX/LX Ethernet standard
- 24 10/100/1000Mbps Ethernet ports, Auto MDI/MDI-X, Virtual Cable Test Support
- 1 Mini-GBIC for 1000Base-SX/LX fiber-optic interface with connection varied by media and distances
- Features Store-and-Forward mode with wire-speed filtering and forwarding rates
- Hardware based 10/100Mbps, half/full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation
- IEEE802.3x flow control for full duplex operation and backpressure for half duplex operation
- Integrated address look-up engine, support 4K absolute MAC addresses, automatic address learning and address aging
- 400KB on chip frame buffer
- 9K Jumbo packet size support
- IEEE802.1q VLAN, up to 256 VLANS, IEEE802.1p four priority with Weight Round Robins
- LACP Link aggregation, port mirroring support
- IGMP Snooping, Storm control
- IEEE802.1d, IEEE802.1w, classic Spanning Tree Algorithm or Rapid Spanning Tree support
- Web, Telnet/Console Command Line management, SNMP v1, v2C
- RMON Group 1, 2, 3, 9
- Virtual Cable Test (VCT) technology provides the mechanism to detect and report potential cabling issues, such as cable opens, cable shorts, etc. on Copper Links.
Specifications
| Hardware
Specification |
Network
Ports
|
24 10/100/1000 Base-T
STP ports
1 Mini-GBIC for 1000Base-SX/LX fiber-optic interface (shared
with port 12) |
Switch
Processing Scheme
|
Store-and-Forward |
Switch
fabric
|
48Gbps |
Throughput
(packet per second)
|
35.7Mbps |
Address
Table
|
4K entries |
Share
data Buffer
|
512KB |
Flow
Control
|
Back pressure for half duplex,
IEEE 802.3x Pause Frame for full duplex |
Dimensions
|
440 x 200 x 44 mm (1U height)
|
Weight
|
2.64 kg |
Power
Requirement
|
100~240 VAC, 50-60
Hz |
Temperature
|
Operating: 0~50 degree
C, Storage -20~70 degree |
| Humidity
|
Operating: 10% to
90%, Storage: 5% to 95% (Non-condensing) |
| Management |
Management
Interface
|
Web, Console, Telnet
and SNMP |
| Features |
RFC 1157 SNMP v1/v2
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1643 Ethernet MIB
RFC 1757 RMON, 4 groups; Group 1, 2, 3, 9. |
Click here to return
WGSW-24010
|
|
|
April 2011 |
The GSW-2400 is designed to allow simultaneous transmission of
multiple packets via an internal high-speed data channel. This means
that it can partition a network more efficiently than bridges or routers
in most environments.
The PLANET GSW-2400 provides 24 Gigabit
Ethernet Switch ports and 2-Mini GBIC interface. The PLANET GSW-2400
delivers 24 ports worth of high-performance, feature-rich integrated
Gigabit Ethernet switching over traditional copper cabling. Each port
supports 10Mbps, 100Mbps, and 1000Mbps as well as half/full mode and can
be easily connected to corporate backbones and servers. The GSW-2400
also provides 2 Mini-GBIC interfaces for fiber extension to uplink to a
server or network backbone. With a 48Gbps non-blocking switch fabric, 4k
MAC Address table, and 802.3x, full-duplex flow control, the GSW-2400
offer wire-speed packet transfer performance without risk of packet
loss.
All 24 RJ-45 copper interfaces support 10/100/1000Mbps
auto-negotiation for optimal speed detection through RJ-45 Category 6, 5
or 5e cables. MDI/MDI-X auto detection is provided for direct wire
connection to any Ethernet device without requiring crossover cables.
Key Features
- Complies with IEEE802.3, 10Base-T, IEEE802.3u, 100Base-TX and IEEE802.3ab, 1000Base-T
- 24-port 10/100/1000 Mbps Ethernet ports and 2 SFP (mini-GBIC) interface
- Features Store-and-Forward mode with wire-speed filtering and forwarding rates
- Hardware based 10/100Mbps, half/full duplex and 1000Mbps full duplex mode, flow control and auto-negotiation
- IEEE802.3x flow control for full duplex operation and Backpressure for half duplex operation
- Integrated address look-up engine, support 4K absolute MAC addresses
- Automatic address learning and address aging
- Supports Auto MDI/MDI-X function
- Support CSMA/CD protocol
- 100~250VAC, 50~60Hz universal Power input
- FCC, CE class A compliant
|
Hardware Specification
|
|
10/100/1000Base-T Ports
|
24
|
|
Mini-GBIC interface
|
2, shared with port 12/24
|
|
Switch Processing Scheme
|
Store-and-Forward
|
|
Switch fabric
|
48Gbps
|
|
Throughput (packet per second)
|
38Mbps
|
|
Address Table
|
4K entries
|
|
Share data Buffer
|
256Kbytes
|
|
Flow Control
|
Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex
|
|
Dimensions
|
430 x 350 x 44 mm (1U height)
|
|
Weight
|
4 kg
|
|
Power Requirement
|
100~240 VAC, 50-60 Hz
|
|
Power Consumption / Dissipation
|
24 Watts, 81.8 BTU/hr
|
|
Temperature
|
Operating: 0~50 degree C, Storage -40~70 degree
|
|
Humidity Operating
|
10% to 90%, Storage: 5% to 95% (Non-condensing)
|
|
Standards Conformance
|
|
Regulation Compliance
|
FCC Part 15 Class A, CE
|
|
Standards Compliance
|
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3x (full-duplex flow control)
|
Click here to return
GSW-2400S
|
|
|
April 2011 |
Features
- Complies with the IEEE802.3, IEEE802.3u, IEEE802.3z and IEEE802.3ab Gigabit Ethernet standard
- 24-port 10/100 Mbps Fast Ethernet Switch
- 2 open slots for 10/100Base-TX, 1000Base-T and 100Base-FX, 1000Base-SX/LX fiber-optic interface with various connection media and distances (FGSW-2420VS)
- 2-port 10/100/1000Base-T Gigabit Ethernet port forming a total 26 twisted-pair cost effective choice
- Each Switching ports support auto-negotiation-10/20, 100/200Mbps supported
- Auto-MDI/MDI-X detection on each RJ-45 port
- Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame flow control (full- duplex)
- High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
- 6K MAC address table, automatic source address learning and ageing
- 4 Mbit embedded memory for packet buffers
- Console and Web interface for Switch basic management and setup
- Support up to 26 port-based VLAN groups
- Support up to 7 Trunk groups, each trunk for up to maximum 4 port with 800Mbps bandwidth
- Port mirroring allows monitoring of the traffic across any port in real time
- Support QoS and bandwidth control on each port
Specifications
| Hardware Specification |
| Ports |
24 10/ 100Base-TX RJ-45
Auto-MDI/MDI-X ports |
| Module
Slot |
2 fixed 10/100/1000Base-T RJ-45 |
|
| Switch
Processing Scheme |
Store-and-forward |
| Address
Table |
6K entries |
| Share
data Buffer |
4 Mbit |
| Throughput
(packet per second) |
6.547Mpps |
Switch
fabric
|
8.8Gbps |
Flow
Control
|
Back pressure for half duplex, IEEE
802.3x Pause Frame for full duplex |
| Dimensions
|
440 x 200 x 44 mm, 1U height |
| Weight
|
2.7 kg |
|
| Power
Requirement |
100~240 VAC, 50-60 Hz |
| Power
Consumption / Dissipation |
30 Watts maximum / 102 BTU/hr maximum
|
| Temperature
|
Operating: 0~50 degree C, Storage -40~70
degree C |
| Humidity
Operating |
10% to 90%, Storage: 5% to 95% (Non-condensing)
|
| Hardware Specification |
| System
Configuration |
Console port and Web interface |
| Port
Configuration |
Port disable/enable
Auto-negotiation disable/enable
10/100Mbps full and half duplex mode selection
Flow control disable/enable |
| Port
Status |
Display each port's disable/enable
status, each port's link status, and speed duplex mode. Flow control
status |
Port
Trunking
|
Support 7 groups of 4-port trunk support |
| VLAN
|
Maximum up to 26 VLAN groups for port-based
VLAN |
| Port
Mirroring |
1 Mirroring port to monitor several
mirrored ports. The monitor modes are Disable, RX, TX, TX& RX |
| QoS |
Allow to assign low and high priority
on each port |
| Bandwidth
Control |
Allow to assign rate control on each
port |
| Standards Conformance
|
Regulation
Compliance
|
FCC Part 15 Class A, CE |
| Standards
Compliance |
IEEE 802.3 (Ethernet),
IEEE 802.3u (Fast Ethernet)
IEEE 802.3z(Gigabit Ethernet)
IEEE 802.3ab (Gigabit Ethernet)
IEEE8023x (Flow control)
IEEE 802.1p QoS |
Click here to return
FGSW-2620VS
|
|
|
